AllProtection.tcl (Stable: v4.8 / Beta: v4.9b4)

[eXtremer]

But if I want to disable it on all channels ?!

Then replace #channel by *

Code: Select all

.chanset * ap:adv - 180 kb 2

Understood, thanks Zircon

[eXtremer]

.chanset * ap:textl + 20 w:k:kb 2
Successfully set modes { ap:textl { + 20 w:k:kb 2 } } on all channels.


I've set this option, but the bot still bans the user!

*** tester` was kicked by Bot (Bad word detected. :: [Fri May 30 11:03:31 2008] :: - Banned 120 minutes)
*** Bot sets mode: +b *!*@???.176.6.149

why ?

[uffs]

because you don't disable it.. + meaning enable and - meaning disable,
also for badwords the setting must like this..

.chanset * ap:swear - 20 w:k:kb 2

[Sir_Fz]

ap:textl is for text flood (lines) and you've enabled it to warn on 1st offence, kick on 2nd, and kickban if repeated for the 3rd time. The kick message you've pasted is for badwords protection, so edit the ap:swear setting and not the ap:textl; if you want to disable it then make sure it's set to - and not +.

[eXtremer]

damn yeah my mistake, sorry!

[eXtremer]

By bot had a ping timeout, when rejoined I saw this in partyline:

[11:00] Tcl error [::AllProtection::joins bnicks]: no such channel record
[11:00] Tcl error [sl_nkflood]: illegal channel: *

what's wrong, can smb tell me ?

[Sir_Fz]

The 2nd error is not related to AllProtection, however the first one is. Which version are you using? and if possible, paste the output of '.set errorInfo'.

[eXtremer]

paste the output of '.set errorInfo'.

don't understand what you ask...".set errorInfo" ?

[Nor7on]

Join to Partyline of ur eggdrop and put:

Code: Select all

.set errorInfo

easy.

[speechles]

Join to Partyline of ur eggdrop and put:

Code: Select all

.set errorInfo

easy.

<random user> .set errorInfo
<eggy> What? You need '.help'

Sure was easy, and yields absolutely nothing of interest. To avoid this, you must change variables within your eggdrop.conf first and either .rehash or .restart your bot directly afterwards.

Code: Select all

# Comment these two lines if you wish to enable the .tcl and .set commands.
# If you select your owners wisely, you should be okay enabling these.
#unbind dcc n tcl *dcc:tcl
#unbind dcc n set *dcc:set

With them set like this, both 'set' and 'tcl' commands will be accessible on your bots partyline. It is a mistake to call this simple. There are steps that must be followed before .set errorInfo will even yield a result other than 'what?'

[eXtremer]

My conf:

Code: Select all

# Comment these two lines if you wish to enable the .tcl and .set commands.
# If you select your owners wisely, you should be okay enabling these.
unbind dcc n tcl *dcc:tcl
unbind dcc n set *dcc:set

Partyline:

Code: Select all

.set
What?  You need '.help'
.set errorInfo
What?  You need '.help'

so ?

[eXtremer]

Sir_Fz, got a question:

# Use .chanset #channel ap:btextl <lines>:<seconds> <lockmode> <locktime> (in DCC, 0:0 to disable)
# Set default rate here:
lappend ap:udefs {ap:btextl "15:7 mR-k lines.flood 60"}

mR-k ?

m = moderate (I know)

R = ??? Unknown MODE (should I change it to "r")

-k - what it does ?

60 = 60 seconds lock-time ?

Waitin`..

[speechles]

My conf:

Code: Select all

# Comment these two lines if you wish to enable the .tcl and .set commands.
# If you select your owners wisely, you should be okay enabling these.
unbind dcc n tcl *dcc:tcl
unbind dcc n set *dcc:set

Partyline:

Code: Select all

.set
What?  You need '.help'
.set errorInfo
What?  You need '.help'

so ?

You proved doing nothing doesn't work. Yay!
Now comment out the unbinds, adding # in front and do like you were told.. silly .. heh

# Comment these two lines if you wish to enable the .tcl and .set commands.
# If you select your owners wisely, you should be okay enabling these.

Code: Select all

#unbind dcc n tcl *dcc:tcl
#unbind dcc n set *dcc:set

[Sir_Fz]

Sir_Fz, got a question:

# Use .chanset #channel ap:btextl <lines>:<seconds> <lockmode> <locktime> (in DCC, 0:0 to disable)
# Set default rate here:
lappend ap:udefs {ap:btextl "15:7 mR-k lines.flood 60"}

mR-k ?

m = moderate (I know)

R = ??? Unknown MODE (should I change it to "r")

-k - what it does ?

60 = 60 seconds lock-time ?

Waitin`..

The modes you want to set when a flood occurs are up to you to be decided. On Dalnet +R means only registered nicks can join the channel, you can change this depending on what network your bot is on (i.e. you can use whatever supported modes you want). k is to set a key for the channel... it's totally useless in this case and only used to display a reason for why the lock is happening, if it's not supported by your network then don't use it.

[eXtremer]

My conf:

Code: Select all

# Comment these two lines if you wish to enable the .tcl and .set commands.
# If you select your owners wisely, you should be okay enabling these.
unbind dcc n tcl *dcc:tcl
unbind dcc n set *dcc:set

Partyline:

Code: Select all

.set
What?  You need '.help'
.set errorInfo
What?  You need '.help'

so ?

You proved doing nothing doesn't work. Yay!
Now comment out the unbinds, adding # in front and do like you were told.. silly .. heh

# Comment these two lines if you wish to enable the .tcl and .set commands.
# If you select your owners wisely, you should be okay enabling these.

Code: Select all

#unbind dcc n tcl *dcc:tcl
#unbind dcc n set *dcc:set

oops sry, I thought it should be uncommented...