my eggdrop can not join in channel with ascii codes :(

Syem · Post by **Syem** » Mon Jul 07, 2008 7:37 am

I have one chan and no have protection for this because my eggdrops can not join this because containts ascii codes .
This is my channel #ÊžÉ”ÆžÉŸ.É™É¥Ê‡.Ê‡ÉÉ¥Ê . Can help me that problem ? I want one tcl to make eggdrop to read this code... ex: Ïž Ú¤ Ð¤ Ü” Üž etc... Or just make read #ÊžÉ”ÆžÉŸ.É™É¥Ê‡.Ê‡ÉÉ¥Ê for join in chan... (sorry for my english) .Thanks.

Post by **Sir_Fz** » Wed Jul 09, 2008 3:26 pm

So you're typing .+chan #ÊžÉ”ÆžÉŸ.É™É¥Ê‡.Ê‡ÉÉ¥Ê in partyline but the bot's entering a different channel?

Syem · Post by **Syem** » Wed Jul 09, 2008 5:15 pm

I try manny commands... not working. Eggdrop join to #žTž_.Ye‡.‡Pe

strikelight · Post by **strikelight** » Wed Jul 09, 2008 6:35 pm

http://forum.egghelp.org/viewtopic.php? ... light=utf8

Syem · Post by **Syem** » Wed Jul 09, 2008 7:48 pm

Ok thx man. But i dont understant what say thommey... how to install what say thommey ? it is a tcl or ?

Alchera · Post by **Alchera** » Thu Jul 10, 2008 9:20 pm

Syem wrote:Ok thx man. But i dont understant what say thommey... how to install what say thommey ? it is a tcl or ?

It's a patch file applied to eggdrop source before (re)compiling.

Syem · Post by **Syem** » Fri Jul 11, 2008 2:52 pm

I try to install this patch ( patch -pl < exemple.patch ) but is not work, i get this error "patch: **** strip count l is not a number". Or this command for install this patch is incorrect ?

Alchera · Post by **Alchera** » Fri Jul 11, 2008 6:56 pm

Try:

Code: Select all

patch -p0 <exemple.patch

Syem · Post by **Syem** » Sat Jul 12, 2008 3:33 am

Hmm.. i try what you say, and result this line :

Code: Select all

root@blu:/dev/shm/eggdrop1.6.19$ patch -p0 <eggdr.patch
can't find file to patch at input line 3
Perhaps you used the wrong -p or --strip option?
The text leading up to this was:
--------------------------
|--- eggdrop1.6.18.original/src/main.h   2006-03-28 04:35:50.000000000
+0200
|+++ eggdrop1.6.18.utf8/src/main.h       2008-04-01 20:57:29.000000000 +0200
--------------------------
File to patch:

In src folder result same error

Code: Select all

Syem · Post by **Syem** » Tue Jul 15, 2008 2:28 pm

Hmm.. no one can help me ?

Post by **nml375** » Tue Jul 15, 2008 4:19 pm

Try using a higher value for -p, ie 1.

Syem · Post by **Syem** » Tue Jul 15, 2008 6:09 pm

Dont work, same error

. Maibe its another command for install this patch.

Post by **nml375** » Tue Jul 15, 2008 6:15 pm

Well, you could always apply the patch manually...

The -p switch simply tells "patch" how much of the file-paths to trim off..
0 means keep as is, 1 means drop the first folder in the path, and so on..

From what you posted, patch looks for the file "main.h" at the relative location of "eggdrop1.6.18.original/src/" (translates to "/dev/shm/eggdrop1.6.19/eggdrop1.6.18.original/src/main.h"). Most likely, it should look for "src/main.h", and this is where -p1 comes in... It tells "patch" to drop the "eggdrop1.6.18.original" part...

Also make sure you're in the correct directory yourself when you issue the command (where you unpacked the source).

Syem · Post by **Syem** » Tue Jul 15, 2008 6:36 pm

I downloaded eggdrop.1.6.18, and i put patch (eggdr.patch) in folder base, and i have install patch with this command "patch -p1 <eggdr.patch" , and result this :

Code: Select all

patch -p1 <eggdr.patch
patching file src/main.h
Reversed (or previously applied) patch detected!  Assume -R? [n] yes
patching file src/tcl.c
Hunk #1 FAILED at 650.
1 out of 1 hunk FAILED -- saving rejects to file src/tcl.c.rej

Post by **nml375** » Tue Jul 15, 2008 6:39 pm

What was the content of the src/tcl.c.rej file?